Elevations

• NOTE – The Industrial Starter set has pieces spread across multiple sheets in some cases. If you find you’re missing a piece, find it on another sheet.
• Glue indicated pieces as shown.
• Make sure that doubled up edges are aligned before drying.
• These create the PLATFORM TOP pieces.

• Clamp pieces every 3 inches or so as shown to dry.

• Assemble support structure as shown.
• Use a generous bead of glue on edges that contact the assembled PLATFORM TOP pieces.
• Please see TIPS & TRICKS video for the most effective method of gluing the plugs.
• Clean any excess glue and allow to dry.

• Assemble similar to previous panel.

• On pieces 18 & 20 ensure all scores are crisply and evenly folded.
• When assembling leg pieces put glue dots in the end of the slots on the larger folded pieces before sliding on the smaller pieces.
• Check legs for square before allowing to dry.

• NOTE – There are 2 extra 02 pieces in the set. That is expected.
• No glue is required.
• Assemble as indicated.
• These pieces fit snugly. Be careful when sliding piece 03 on the double plugs to not bend or tear any pieces. Slow and steady wins this race.

• Glue and assemble as indicated.

• Please see TIPS & TRICKS video for the most effective method of gluing the plugs.

• No glue is required.
• Legs assemble onto feet as indicated.

• No glue is required.
• Platforms assemble onto legs & feet as indicated.

• An assembled platform looks like this diagram.
• The platforms, legs, extenders, and feet can be combined in may ways.

• NOTE – There are 2 extra 26 pieces in the set. That is expected.
• When assembling steps pieces put glue dots in the end of the slots on the side riser pieces before sliding on the smaller tread pieces.
• Ensure steps side risers are straight up and down before allowing to dry.

Containers

• On pieces 66 & 67 ensure all scores are crisply and evenly folded.
• Then glue, clamp, and let dry.

• On piece 69 ensure all scores are crisply and evenly folded.
• Then ensure piece 68 is glued into the area indicated as centered as possible on all edges.

• Clamp previous piece as shown.
• Glue additional piece 68 into place, with similar tolerances on the edges.

• Wrap piece 69 fully around, gluing additional piece 68 into place.
• Clamp as shown and allow to dry.
• This forms the CONTAINER EXTERIOR piece.

• Glue pieces 64 and 65 to each other as shown. Their back sides should be glued.
• Piece 64 should be as centered as possible within piece 65.
• Clamp and allow to dry.
• Two of these form the END PIECES for the Container.

• Run a thin line of glue along the outside edge of piece 64 on both assembled END PIECES.
• Insert them into the ends of the assembled CONTAINER EXTERIOR piece.
• Clean any excess glue and allow to dry.

• Glue and assemble as indicated.
• Please see TIPS & TRICKS video for the most effective assembly method.

• OPTIONAL – You can glue doors onto one or both ends of your container as desired.

Cover Pieces

• Make sure glue marks and targets match size and shape, and that doubled up edges are aligned before drying.
• Glue pieces 47 & 48 together first and let dry.
• Tabs on the edge of piece 48 will only fit into the front side of slots in piece 46 in one way.
• This will make a BEAM piece.

• When gluing two assembled BEAM pieces together make sure the tear drop shaped glue marks and targets align.
• Also ensure that the indicator line adjacent to the glue mark on piece 46 is lined up with the edge of the other assembled BEAM piece.

• Glue and assemble as indicated.

• The finished piece should look like so.

• When assembling cover pieces put glue dots in the end of the slots on the large face pieces before sliding on the leg support pieces.
• Then before the glue dries, make sure the leg support pieces are perpendicular to the large face pieces.

• When assembling cover pieces putting glue dots in the inside of the slots in the large face pieces before sliding on the leg support pieces.
• Then before the glue dries, make sure the leg support pieces are perpendicular to the large face pieces.

• When assembling cover pieces putting glue dots in the inside of the slots in the large face pieces before sliding on the leg support pieces.
• Then before the glue dries, make sure the leg support pieces are perpendicular to the large face pieces.

• Before assembling, make sure all crate pieces are the same color. Some pieces are only colored on one side.
• Make sure glue marks and targets match size and shape, and that doubled up edges are aligned before drying.
• Glue pieces 31a & 31b as well as 32a & 32b together first and let dry.
• On piece 30 ensure all scores are crisply and evenly folded.

Ladders & Catwalks

• There are 3 sizes of ladders on your sheets that all assemble in the same way.
• Please see TIPS & TRICKS video for the most effective assembly method.
• When attaching side pieces to the ladder piece, insert tabs into slots on the front rolled edge face of the side pieces.

• Make sure that doubled up edges are aligned before drying.
• Glue pieces 27 & 28 together first and let dry.
• When attaching pieces 29a & 29b, insert tabs into slots on the front rolled edge face of the side pieces.
• Make sure side pieces are straight up and down before drying.

• Make sure that doubled up edges are aligned before drying.
• Glue pieces 44 & 45 together first and let dry.
• When attaching pieces 43a & 43b, insert tabs into slots on the front rolled edge face of the side pieces.
• Make sure side pieces are straight up and down before drying.