Elevations

  • NOTE – The Industrial Starter set has pieces spread across multiple sheets in some cases. If you find you’re missing a piece, find it on another sheet.
  • Glue indicated pieces as shown.
  • Make sure that doubled up edges are aligned before drying.
  • These create the PLATFORM TOP pieces.

  • Clamp pieces every 3 inches or so as shown to dry.
  • Assemble support structure as shown.
  • Use a generous bead of glue on edges that contact the assembled PLATFORM TOP pieces.
  • Please see TIPS & TRICKS video for the most effective method of gluing the plugs.
  • Clean any excess glue and allow to dry.
Tips & Tricks
  • Assemble similar to previous panel.
  • On pieces 18 & 20 ensure all scores are crisply and evenly folded.
  • When assembling leg pieces put glue dots in the end of the slots on the larger folded pieces before sliding on the smaller pieces.
  • Check legs for square before allowing to dry.
  • NOTE – There are 2 extra 02 pieces in the set. That is expected.
  • No glue is required.
  • Assemble as indicated.
  • These pieces fit snugly. Be careful when sliding piece 03 on the double plugs to not bend or tear any pieces. Slow and steady wins this race.
  • Glue and assemble as indicated.
  • Please see TIPS & TRICKS video for the most effective method of gluing the plugs.
Tips & Tricks
  • No glue is required.
  • Legs assemble onto feet as indicated.
  • No glue is required.
  • Platforms assemble onto legs & feet as indicated.

  • An assembled platform looks like this diagram.
  • The platforms, legs, extenders, and feet can be combined in may ways.
  • NOTE – There are 2 extra 26 pieces in the set. That is expected.
  • When assembling steps pieces put glue dots in the end of the slots on the side riser pieces before sliding on the smaller tread pieces.
  • Ensure steps side risers are straight up and down before allowing to dry.


Container

  • On pieces 66 & 67 ensure all scores are crisply and evenly folded.
  • Then glue, clamp, and let dry.

  • On piece 69 ensure all scores are crisply and evenly folded.
  • Then ensure piece 68 is glued into the area indicated as centered as possible on all edges.

  • Clamp previous piece as shown.
  • Glue additional piece 68 into place, with similar tolerances on the edges.

  • Wrap piece 69 fully around, gluing additional piece 68 into place.
  • Clamp as shown and allow to dry.
  • This forms the CONTAINER EXTERIOR piece.

  • Glue pieces 64 and 65 to each other as shown. Their back sides should be glued.
  • Piece 64 should be as centered as possible within piece 65.
  • Clamp and allow to dry.
  • Two of these form the END PIECES for the Container.

  • Run a thin line of glue along the outside edge of piece 64 on both assembled END PIECES.
  • Insert them into the ends of the assembled CONTAINER EXTERIOR piece.
  • Clean any excess glue and allow to dry.

  • Glue and assemble as indicated.
  • Please see TIPS & TRICKS video for the most effective assembly method.
Tips & Tricks
  • OPTIONAL – You can glue doors onto one or both ends of your container as desired.


Cover Pieces

  • Make sure glue marks and targets match size and shape, and that doubled up edges are aligned before drying.
  • Glue pieces 47 & 48 together first and let dry.
  • Tabs on the edge of piece 48 will only fit into the front side of slots in piece 46 in one way.
  • This will make a BEAM piece.
Tips & Tricks
  • When gluing two assembled BEAM pieces together make sure the tear drop shaped glue marks and targets align.
  • Also ensure that the indicator line adjacent to the glue mark on piece 46 is lined up with the edge of the other assembled BEAM piece.
  • Glue and assemble as indicated.
  • The finished piece should look like so.
  • When assembling cover pieces put glue dots in the end of the slots on the large face pieces before sliding on the leg support pieces.
  • Then before the glue dries, make sure the leg support pieces are perpendicular to the large face pieces.
  • When assembling cover pieces putting glue dots in the inside of the slots in the large face pieces before sliding on the leg support pieces.
  • Then before the glue dries, make sure the leg support pieces are perpendicular to the large face pieces.
  • When assembling cover pieces putting glue dots in the inside of the slots in the large face pieces before sliding on the leg support pieces.
  • Then before the glue dries, make sure the leg support pieces are perpendicular to the large face pieces.
  • Before assembling, make sure all crate pieces are the same color. Some pieces are only colored on one side.
  • Make sure glue marks and targets match size and shape, and that doubled up edges are aligned before drying.
  • Glue pieces 31a & 31b as well as 32a & 32b together first and let dry.
  • On piece 30 ensure all scores are crisply and evenly folded.

Ladders & Catwalks

  • There are 3 sizes of ladders on your sheets that all assemble in the same way.
  • Please see TIPS & TRICKS video for the most effective assembly method.
  • When attaching side pieces to the ladder piece, insert tabs into slots on the front rolled edge face of the side pieces.
Tips & Tricks
  • Make sure that doubled up edges are aligned before drying.
  • Glue pieces 27 & 28 together first and let dry.
  • When attaching pieces 29a & 29b, insert tabs into slots on the front rolled edge face of the side pieces.
  • Make sure side pieces are straight up and down before drying.
  • Make sure that doubled up edges are aligned before drying.
  • Glue pieces 44 & 45 together first and let dry.
  • When attaching pieces 43a & 43b, insert tabs into slots on the front rolled edge face of the side pieces.
  • Make sure side pieces are straight up and down before drying.